Mono-material packaging is a film or rigid structure built so the package mass is dominated by a single polymer family, designed to qualify for collection in the recycling stream that family belongs to. The phrase has no single global threshold. The dominant North American framework, the Association of Plastic Recyclers' Design Guide, sets "Preferred" at greater than 90% of one polymer (PE or PP) by weight[1][2]. Peer-reviewed literature uses 95%[4]. The operative threshold in any specific case is whichever scheme covers the market the product is sold into. A mono-material structure suits some applications; product protection, line performance and market requirements determine where it fits.
What mono-material means
Mono-material describes how a pack is built. Its dominant polymer must also fit a recycling stream available in the destination market if the pack is to have a practical recovery route. Two packs built chiefly from the same polymer may therefore have different outcomes after use.
It is not the same as "single material." Mono-material structures contain inks, adhesives, additives, tie layers, and barrier coatings. The composition rules in the major frameworks define how much of those secondary components is tolerated before the structure no longer qualifies. The Association of Plastic Recyclers, the dominant North American framework, allows up to 5% EVA copolymers, up to 5% polybutenes, and up to 20% ionomer copolymers within Preferred mono-PE without disqualifying the structure[1]. A buyer reading "mono-material" on a supplier spec without those tolerances spelled out does not have the full picture.
It is not the same as "recyclable" either. A mono-PE structure that meets APR Preferred-tier criteria is recyclable in markets that collect PE film. In a market that does not collect PE film, the same structure ends up in landfill. The design guide tells you whether the structure could qualify for a recycling stream. Collection in the market where the pack is sold determines whether that route is available in practice.
How thresholds differ
There is no global mono-material threshold. The closest the industry has to a settled standard is APR's PE Flexible and PP Flexible Design Guides, both of which set Preferred at greater than 90% of the target polymer by weight[1][2]. APR's PP guide references ISO 19069 as the compositional standard.
Peer-reviewed packaging research commonly uses 95% as the mono-material definition[4]. CEFLEX, the European industry consortium covering flexible packaging, takes a structural rather than percentage-based approach, with Phase 1 design guidelines focused on polyolefin-based structures (mono-PE, mono-PP, and PE/PP mixes) compatible with European recycling streams[3]. Jurisdiction-specific EPR schemes are starting to define their own modulation criteria, sometimes tracking APR or CEFLEX, sometimes setting their own.
The relevant threshold depends on the scheme used in the destination market. A structure shipping into Oregon under the Recycling Modernization Act is judged against criteria CAA accepts. A structure shipping into Quebec or Ontario is judged against the relevant provincial PRO's requirements. A structure shipping into the EU is judged against CEFLEX-aligned national schemes. That makes the destination market an essential part of the material brief.
Commercial reasons to consider it
The Flexible Packaging Association reports US flexible packaging at roughly $41.5 billion in 2022 sales, which makes it the second-largest US packaging segment at around 21% of the $180.3 billion US packaging market. Food, retail and institutional, accounts for about 50% of flexible packaging shipments[6]. These figures give useful context for the volume of material affected by packaging choices.
EPR fees are another reason to compare structures. Schemes that charge different per-pound fees by recyclability are now in force in some North American markets, and the structural choice is starting to read as a financial choice. Oregon's 2026 producer fee schedule, published by Circular Action Alliance in October 2025, prices PE flexible film at 43.0 c/lb, PP flexible film at 102.0 c/lb, and Plastic Laminates and Other Flexible Plastic Packaging at 102.0 c/lb[5]. A switch from a non-recyclable laminate to a mono-PE structure that qualifies for PE film collection cuts the per-pound EPR fee in Oregon by more than half.
Other US states (California, Colorado, Maine, Minnesota) and Canadian provinces (Ontario, BC, Quebec) are rolling out parallel schemes on different timelines. Australia operates the APCO scheme. Each jurisdiction uses its own rules and rates. Compare the actual markets for a product rather than applying a single global average.
Applications where it may fit
A mono-material design may be worth assessing when:
- The destination market has functional collection for the target polymer family. PE film collection is broader than PP flexible collection in most North American markets at present, primarily through Store Drop-off labelling under the How2Recycle programme[1]. Curbside collection of flexible film is rarer.
- The product's barrier and shelf-life targets can be met within the coating allowances of the relevant framework. APR allows EVOH up to 10% by weight in coextruded mono-PE and up to 6% in mono-PP, with maleated tie layers in either case. Vacuum-deposited SiOx and AlOx are accepted for both[1][2].
- EPR fee modulation in the destination market makes the structural choice commercially obvious[5].
- The line can run the structure with adjustments rather than full retooling.
Another structure may be more suitable when:
- The product needs barrier the family cannot deliver even with the coatings the framework permits. An oxygen-sensitive coffee product with a twelve-month ambient shelf life would need careful barrier assessment.
- The thermal regime exceeds the polymer family. Hot-fill and retort push designs toward mono-PP or out of mono-material entirely. PE cannot absorb retort heat.
- The destination market does not collect the polymer family at any meaningful scale. A technically recyclable structure that has nowhere to go is treated like a non-recyclable one in the EPR schedule that prices it.
- Brand identity depends on metallised laminate aesthetics that exceed APR's surface-area thresholds for metallised content[1][2].
How to assess it for a product
A product-specific assessment should cover these points:
- Identify the destination markets and confirm what recycling collection actually exists in each one. Do not assume.
- Check the dominant scheme for each market (APR, CEFLEX, jurisdiction-specific PRO) and read the Preferred-tier composition rules.
- Compare the product's barrier and shelf-life targets against what mono-PE or mono-PP can deliver within those rules, including with the permitted coatings.
- Calculate the EPR fee delta between the current structure and the candidate mono-material structure under each destination's scheme. Oregon is the cleanest US worked example currently.
- Confirm how the structure runs on the line and include any production changes in the cost comparison.
- Ask each candidate supplier for the applicable declarations, recognition documents and test reports. Check that those documents refer to the proposed structure and the market where it will be sold.
How Terralign reviews mono-material options
Terralign reviews mono-material proposals against the food, packing line, target markets and available supplier data. Our technical lead has worked across plastic films, trays and paper-based formats. If a client needs help approaching suppliers after the review, we can discuss that as separate work and disclose any relevant commercial relationship.
For an unfamiliar structure or supplier, we identify which properties and claims can be checked from the documents and which need testing or further supplier evidence. We discuss those limits with the client before treating a proposal as suitable for the application.
References
- Association of Plastic Recyclers. Design Guide for Plastics Recyclability — PE Flexible. Last updated March 30, 2026. plasticsrecycling.org/apr-design-hub/apr-design-guide/pe-flexible/
- Association of Plastic Recyclers. Design Guide for Plastics Recyclability — PP Flexible. Last updated March 30, 2026. plasticsrecycling.org/apr-design-hub/apr-design-guide/pp-flexible-guidance/
- CEFLEX. Designing for a Circular Economy guidelines (D4ACE), Phase 1. June 2020, factsheet updated December 2023. guidelines.ceflex.eu
- Foppa, F., Lecce, L., et al. Effect of the shifting from multi-layer systems towards recyclable mono-material flexible films on food shelf-life. Sustainable Production and Consumption, 2024. sciencedirect.com
- Circular Action Alliance. 2026 Oregon Producer Fee Schedule. Published October 29, 2025. circularactionalliance.org/producer-resource-center
- Flexible Packaging Association. Industry Facts and Figures. As of September 2023. flexpack.org/facts-and-figures