OPP/CPP polypropylene laminate

What OPP/CPP is in practice

OPP/CPP is a two-layer or multi-layer film structure where the outer layer is oriented polypropylene (typically biaxially oriented BOPP, or machine-direction oriented OPP) and the sealing layer is cast polypropylene (CPP). The outer layer provides stiffness, print quality, optical clarity, and dimensional stability through the line. The CPP inner layer provides clean heat sealing with a sealing window typically initiating around 130 to 150°C depending on grade.

The structure runs widely on flow wrap (horizontal pillow pack) for snacks, confectionery, and hard cheese, on vertical form-fill-seal (VFFS) for some snack and dry-goods formats, and on pre-made pouch filling. The combination of stiffness, hot tack, and tracking stability at line speed is what made OPP/CPP the industry default for flow wrap.

Why mono-PP qualification matters here

Both BOPP and CPP are polypropylene. Different orientations of the same base polymer are treated as the same material under both APR and Canada Plastics Pact framework rules. The Canada Plastics Pact "Pathways to Mono-Material Flexible Plastic Packaging" guidance is explicit on this point: "Bi-axially oriented and non-oriented forms of the same base polymer (i.e., either PE or PP) are considered to be mono-materials"[1].

That makes OPP/CPP one of the simpler structures to design as mono-PP. A simple two-layer BOPP/CPP construction with an inks-and-adhesives system inside framework allowances can qualify as APR Preferred mono-PP at greater than 90% PP by weight measured per ISO 19069[2]. Under the Canadian GDR 6, the same structure qualifies as mono-PP at minimum 90% PP, with barrier and additive use limited to the APR Design Guideline allowances and a maximum of 10% barrier layer (one layer)[1].

This is genuinely useful: a buyer specifying flow wrap snacks does not have to redesign away from a familiar OPP/CPP structure to claim recyclable mono-material status. They have to confirm the inks, adhesives, and any barrier additions stay within framework rules.

What pushes OPP/CPP out of mono-PP

The structure stops qualifying as mono-PP when the package mass shifts away from PP or when disqualifying components are added. Three common ways it happens[1][2]:

  • EVOH above the framework limit. APR's PP Flexible guidance accepts EVOH inside Preferred mono-PP only up to 6.0 wt%, with PP-g-MAH tie layers and an EVOH-to-tie-layer ratio at or below 2:1. Above that, the structure falls out of Preferred.
  • Metallisation above surface-area thresholds. Vapour-deposited metallisation is accepted as Preferred only when the metallised content stays below the surface-area limits in APR's RES-SORT-03b. A fully metallised flow wrap typically exceeds those thresholds and would need testing.
  • PET, PVC, PVDC, paper, or aluminium foil layers. Any of these in the structure renders the package non-recyclable in the PP film stream regardless of percentage. Met-OPP/CPP/PET reverse-printed structures are common in snacks but cannot be mono-PP.

The decision becomes commercial: does the product really need the high-barrier layer or the metallised aesthetic, or can it run on a simpler OPP/CPP structure that earns the mono-PP classification? In a market where PP flexible collection is unreliable and the EPR fee penalty does not yet apply (Oregon's 2026 schedule treats both PP flexible and laminate at 102 ¢/lb regardless), the answer may be different than in a market where the modulation is meaningful.

Where OPP/CPP is the right answer

OPP/CPP is the established answer when:

  • The application is flow wrap, VFFS for snacks or confectionery, or pre-made pouch filling.
  • The product is moderately oxygen-tolerant and moisture-tolerant (typical hard cheese, biscuits, baked snacks, confectionery) and barrier targets can be met with the simpler structure or with a within-framework EVOH/SiOx coating.
  • Aesthetic demands fit OPP's clarity and printability without needing metallised laminate finishes.
  • Line speed and tracking stability matter and the existing line is set up for OPP-sealing tooling.

OPP/CPP is generally not the right answer when:

  • The product is highly oxygen-sensitive (extruded snacks with high oil content targeting 9 to 12 month shelf life) and the barrier need exceeds what 6 wt% EVOH plus a SiOx coating can deliver. These products often run on PET-met-OPP-CPP or similar multi-material structures and cannot be mono-PP.
  • The brand identity depends on a fully metallised laminate finish for premium positioning. The metallised surface area required for the aesthetic typically exceeds APR thresholds.
  • The destination market lacks PP flexible collection infrastructure and the producer cannot absorb the higher EPR fee tier. In Oregon, mono-PP without verified PP-stream collection still pays 102 ¢/lb, the same as a non-recyclable laminate[3].

References

  1. Canada Plastics Pact. Pathways to Mono-Material Flexible Plastic Packaging. Updated May 2025. plasticspact.ca
  2. Association of Plastic Recyclers. Design Guide for Plastics Recyclability — PP Flexible. Last updated March 30, 2026. plasticsrecycling.org/apr-design-hub/apr-design-guide/pp-flexible-guidance/
  3. Circular Action Alliance. 2026 Oregon Producer Fee Schedule. Published October 29, 2025. circularactionalliance.org/producer-resource-center

Have a packaging decision to work through? Contact Terralign.