What buyers in this category face
Snacks and confectionery is one of the largest single end-uses of flexible packaging globally. The category covers products as different as oxygen-sensitive oily extruded snacks, low-barrier baked biscuits, hard candies, chocolate bars, and granola bars, and the packaging answer differs substantially across them.
The shared problem set: most snacks lose acceptability through one or more of three failure modes. Oxidation drives rancidity in fatty products. Moisture absorption destroys crispness in dry products. Aroma loss erodes brand experience in flavour-driven products. The packaging has to address whichever combination of those matters for the specific product, on a high-speed line, at a per-pack cost the category can absorb.
The buying decision typically lands somewhere on a spectrum from "simplest mono-PP that meets the spec" (low-barrier biscuits, hard confectionery) to "high-barrier metallised laminate" (oily extruded snacks with 9 to 12 month ambient shelf life targets).
Performance requirements
Four parameters drive material selection for snacks:
- Oxygen barrier. For oily extruded snacks targeting 9 to 12 month shelf life, oxygen transmission rate (OTR) typically needs to sit below 1 cc/100 in²/24 hr, which is below what plain mono-PP or mono-PE structures deliver without a barrier addition. The Canada Plastics Pact mono-material guidance is direct on this: high oxygen barrier MAP films at OTR less than 1 cc/100 in²/24 hr require a thin barrier layer such as metallisation, SiOx, AlOx, EVOH coextrusion, nanoclay, or PVOH coating[1].
- Moisture barrier. Critical for crisp products and any snack where retained crunch is a quality attribute. Polyolefins (PE and PP) are inherently better at moisture barrier than oxygen barrier; the structural decision usually centres on oxygen.
- Hot tack and seal reliability at line speed. Snack lines typically run at 60 to 200 cycles per minute. Hot tack matters because the seal must hold under tension immediately after the jaw releases. Line failures here are expensive.
- Coefficient of friction (COF) and tracking stability. The film has to run cleanly through high-speed equipment without stretching, dragging, or printing register drift.
The packaging formats actually in use
Flow wrap (horizontal pillow pack). The dominant format for chocolate bars, biscuits, granola bars, individual confectionery, and many extruded snacks. OPP/CPP coextruded or laminated structures run the bulk of the volume. Where higher barrier is needed, the structure becomes PET-met-OPP/CPP or similar multi-material laminate.
Vertical form-fill-seal (VFFS). The dominant format for filled bag formats: crisps, popcorn, kettle chips, pretzels, mixed nuts. Structures range from mono-OPP and OPP/CPP for moderate-barrier products to metallised laminates (typically PET or OPP-met laminated to a CPP or PE sealant) for high-barrier oily snacks. Nitrogen flush is common to displace oxygen in the headspace.
Pre-made stand-up pouches. Increasingly used for premium snacks where shelf presentation matters. Structures range from PET/PE for mid-barrier to PET/met-PET/PE or PET/AlOx-PET/PE for high-barrier.
Note that "mono-material" in this context generally refers to the substrate family. Metallised mono-PP (where the entire structure is PP including a metallised PP outer) is technically possible but constrained by APR's metallisation surface-area thresholds[2].
Materials worth shortlisting for snacks
- OPP/CPP polypropylene laminate — the workhorse for flow wrap and many VFFS formats. Mono-PP qualifying when the structure stays within APR and Canada Plastics Pact framework rules. Right answer for moderate-barrier confectionery, biscuits, and many low-to-mid-oil snacks.
- Mono-PP flexible packaging — the canonical reference for the polymer family. Includes considerations for OPP, BOPP, CPP, and the mono-PP route specifically.
- Mono-PE flexible packaging — the recyclable alternative for VFFS bags of frozen snacks, dry mixes, and granola products where PE film collection is the destination market path.
For high-barrier snacks where a multi-material laminate is the right answer (oxygen-sensitive oily products with long ambient shelf life), the structure is supplier- and product-specific. The packaging brief is the right place to work through whether the metallised laminate is justified by the shelf-life target or whether a coated mono-material structure can hit the spec at lower long-term cost under EPR.
Compliance considerations
Snacks and confectionery packaging is regulated as a food-contact material in every market Terralign covers. The frameworks are jurisdiction-specific:
- United States. FDA under the Federal Food, Drug and Cosmetic Act. Polypropylene cleared under 21 CFR 177.1520 (olefin polymers); inks, lacquers, adhesives, and barrier coatings have their own clearances or Food Contact Notifications. Supplier Declaration of Compliance must cover the specific structure.
- Canada. Health Canada under the Food and Drugs Act and Regulations.
- Mexico. COFEPRIS.
- Australia and New Zealand. FSANZ Standard 1.4.3.
- European Union. Regulation (EC) No 1935/2004 (general framework) and (EU) No 10/2011 (plastics). EU compliance does not establish FDA compliance; structures shipping into multiple jurisdictions need separate declarations.
EPR exposure varies by destination market. Oregon's 2026 producer fee schedule treats PP flexible film at 102 ¢/lb and plastic laminates at the same rate, meaning a snacks SKU shipping into Oregon today does not earn a fee modulation discount for switching from a metallised laminate to a mono-PP structure unless that mono-PP structure is independently certified for collection[3]. In jurisdictions with PP collection infrastructure, the modulation reverses.
How Terralign approaches snacks sourcing
Terralign has direct sourcing experience across flow wrap and VFFS formats for snacks and confectionery. The right structural answer depends on barrier targets, shelf-life requirements, line speeds, line tooling, and the destination markets' collection and EPR profile. Where mono-PP via OPP/CPP is realistic for the spec, we say so. Where the product genuinely needs a high-barrier metallised structure, we say that too, and source it from a vetted manufacturing partner with the documented food-contact compliance the destination jurisdiction requires.
References
- Canada Plastics Pact. Pathways to Mono-Material Flexible Plastic Packaging. Updated May 2025. plasticspact.ca
- Association of Plastic Recyclers. Design Guide for Plastics Recyclability — PP Flexible. Last updated March 30, 2026. plasticsrecycling.org/apr-design-hub/apr-design-guide/pp-flexible-guidance/
- Circular Action Alliance. 2026 Oregon Producer Fee Schedule. Published October 29, 2025. circularactionalliance.org/producer-resource-center